Closeout certificates, explained state by state
A job isn't really finished until the trade's own compliance certificate is handed over — and the same certificate has a different name depending on which state the job is in. Here's what's actually required, and where the common mix-ups happen.
This page is general information only, based on publicly available sources as at the date this page was last reviewed (see the sources listed further down this page for that date). It is not legal, compliance, or insurance advice, is not exhaustive, and may not reflect the most current requirements -- regulations, licensing rules, and insurance thresholds change, and requirements can vary by project, site, and contract. Always verify current requirements directly with the relevant state or territory regulator, your insurer, or a qualified advisor before relying on anything here.
The short answer
Electrical work in Victoria is closed out with a Certificate of Electrical Safety (COES, Energy Safe Victoria). The same kind of document in NSW is called a Certificate of Compliance for Electrical Work (CCEW, Building Commission NSW). Queensland calls it a Certificate of Testing and Safety or a Certificate of Testing and Compliance under its own Electrical Safety Regulation. Plumbing and drainage work has its own, entirely separate compliance certificate again. None of these names are interchangeable, and using the wrong one for the wrong state is a genuine, common mistake.
This page covers electrical and plumbing closeout certificates specifically, where the terminology and penalties below were confirmed directly against the regulator. Other states and trades have their own equivalent regimes — treat this as a starting point and confirm the current requirement for your own state and trade before relying on it.
Electrical work has its own certificate — and its own name, per state
In Victoria, a Registered Electrical Contractor or Licensed Electrical Worker issues a Certificate of Electrical Safety (COES) under the Electricity Safety Act 1998. "Prescribed" work — switchboards, mains, earthing, solar and battery installs — needs independent inspection by a Licensed Electrical Inspector before it's energised, and the customer's copy is due within 4 days of that inspection. "Non-prescribed" work — lights, power points — needs no inspection, with the copy due within 30 days. In NSW, the equivalent document is a Certificate of Compliance for Electrical Work (CCEW), lodged with Building Commission NSW. Queensland's Electrical Safety Regulation uses yet another pair of names — a Certificate of Testing and Safety for equipment, and a Certificate of Testing and Compliance for installation work. Three states, three different certificate names, for broadly the same underlying obligation.
Other trades have their own paperwork too
Electrical work isn't the only trade with a closeout certificate obligation — in NSW, plumbing and drainage work carries its own, separate Certificate of Compliance, administered the same way but entirely independent of anything to do with electrical work. A builder tracking only the electrical certificate and assuming "paperwork's sorted" can still be missing a plumbing certificate for the exact same job.
What happens if it's missing
This isn't a formality either side can skip. In NSW, failing to supply a CCEW to Building Commission NSW carries an on-the-spot fine of up to $1,000, and electrical work that breaches the technical standards can carry penalties up to $550,000. In Victoria, failing to meet COES requirements is a criminal offence under the Electricity Safety Act, and can trigger disciplinary action against the licence holder directly — not just the company.
What ComplySite tracks instead
ComplySite doesn't tell you which certificate a specific job needs — that's a question for your own state's regulator. What it does is track, per subcontractor and per project, whether the closeout certificate the job needs has actually been collected, the same way it already tracks a licence or an insurance certificate: missing or overdue shows up on the dashboard, not just in an inbox you have to remember to check after the job's already finished.
Check the current position directly
- Energy Safe Victoria — Certificates of Electrical Safety
Source for the Victorian COES definition, timing and offence details above
- Building Commission NSW — CCEW requirements & penalties
Source for the NSW CCEW penalty figures above
- Building Commission NSW — Plumbing compliance documents
Source for the separate NSW plumbing Certificate of Compliance above
- Electrical Safety Regulation 2013 (Qld), ss 25–26
Source for Queensland's certificate names above — example states shown, confirm with your own
This page was last reviewed against those sources on 13 November 2026. See the full sources list for every state and territory regulator.
Frequently asked questions
What's a Certificate of Electrical Safety (COES)?
It's Victoria's term specifically, issued by a Registered Electrical Contractor or Licensed Electrical Worker under the Electricity Safety Act 1998. "Prescribed" work (switchboards, mains, earthing, solar/battery) needs independent inspection by a Licensed Electrical Inspector before it's energised, with the customer's copy due within 4 days of that inspection; "non-prescribed" work (lights, power points) needs no inspection, with the copy due within 30 days.
Does every state call it the same thing?
No -- this is the single most common mix-up. Victoria's Certificate of Electrical Safety (COES) is a Victoria-specific term (Energy Safe Victoria). NSW's equivalent is called a Certificate of Compliance for Electrical Work (CCEW), administered by Building Commission NSW. Queensland uses a Certificate of Testing and Safety or a Certificate of Testing and Compliance under its own Electrical Safety Regulation -- not "COES." Using the wrong state's term on the wrong job is a genuinely common mistake.
What happens if a subcontractor doesn't provide one?
In NSW, failing to supply a CCEW to Building Commission NSW carries an on-the-spot fine of up to $1,000, and electrical work that breaches the technical standards can carry penalties up to $550,000. In Victoria, failing to meet COES requirements is a criminal offence under the Electricity Safety Act and can trigger disciplinary action against the licence itself. These aren't paperwork formalities -- they're enforced.
Is it just electrical work?
No. Plumbing and drainage work has its own, separate compliance certificate requirement (a Certificate of Compliance in NSW, administered the same way), entirely apart from anything to do with electrical work. Each trade's closeout paperwork is its own obligation, not a single generic "sign-off."
Can ComplySite tell me which certificate a specific job needs?
No -- that's a question for your own state's regulator, since it depends on the trade, the state, and sometimes the specific type of work done. What ComplySite does is track, per subcontractor and per project, whether the certificate the job needs has actually been collected -- the same way it tracks a licence or an insurance certificate.